Arduino MEGA 2560 a ramps 1.4
Kopil jsem si na hraní Arduino MEGA 2560 a ramps 1.4 v Čině.
https://www.ebay.com/itm/Mega-2560-R3-R ... 2749.l2649
Možná z toho jednou bude 3D tiskárna a spíše jen na učení.
Mám představu, že to budu ovládat skzeva Printrun (pronterface) a USB.
Napadlo mne jako firware použít Průšův. Ovšem při pokusu nahrát ho z pruša Slic3r do ardujna nahrávání selhává.
Potřeboval bych poradit jaký firmware a odkud a jak dostat do toho ardujna, ramps 1.4. Proto, že je to na učení tak co nejjednodušší. Třeba *.hex bych do toho dostat uměl.
https://www.ebay.com/itm/Mega-2560-R3-R ... 2749.l2649
Možná z toho jednou bude 3D tiskárna a spíše jen na učení.
Mám představu, že to budu ovládat skzeva Printrun (pronterface) a USB.
Napadlo mne jako firware použít Průšův. Ovšem při pokusu nahrát ho z pruša Slic3r do ardujna nahrávání selhává.
Potřeboval bych poradit jaký firmware a odkud a jak dostat do toho ardujna, ramps 1.4. Proto, že je to na učení tak co nejjednodušší. Třeba *.hex bych do toho dostat uměl.
Nedaří se mi printScrin tak alespoň takto:
avrdude-slic3r -v -p atmega2560 -c wiring -P COM9 -b 115200 -D -U flash:w:0:C:\D A T A\arduino\PRŮŠA\prusa3d_fw_MK3S_3_8_1_2869.hex:i
avrdude-slic3r: Version 6.3-20160220-prusa3d, compiled on Sep 16 2019 at 11:15:49
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
Using Port : COM9
Using Programmer : wiring
Overriding Baud Rate : 115200
AVR Part : ATmega2560
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 10 8 0 no 4096 8 0 9000 9000 0x00 0x00
flash 65 10 256 0 yes 262144 256 1024 4500 4500 0x00 0x00
lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : Wiring
Description : Wiring
Programmer Model: AVRISP
Hardware Version: 15
Firmware Version Master : 2.10
Vtarget : 0.0 V
SCK period : 0.1 us
avrdude-slic3r: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.01s
avrdude-slic3r: Device signature = 0x1e9801 (probably m2560)
avrdude-slic3r: safemode: hfuse reads as D8
avrdude-slic3r: safemode: efuse reads as FD
avrdude-slic3r: reading input file "C:\D A T A\arduino\PRŮŠA\prusa3d_fw_MK3S_3_8_1_2869.hex"
avrdude-slic3r: writing flash (241630 bytes):
avrdude-slic3r: stk500v2_command(): command failed
Writing | ################################################## | 100% 39.09s
avrdude-slic3r: 241630 bytes of flash written
avrdude-slic3r: verifying flash memory against C:\D A T A\arduino\PRŮŠA\prusa3d_fw_MK3S_3_8_1_2869.hex:
avrdude-slic3r: load data flash data from input file C:\D A T A\arduino\PRŮŠA\prusa3d_fw_MK3S_3_8_1_2869.hex:
avrdude-slic3r: input file C:\D A T A\arduino\PRŮŠA\prusa3d_fw_MK3S_3_8_1_2869.hex contains 241630 bytes
avrdude-slic3r: reading on-chip flash data:
Reading | ################################################## | 100% 27.48s
avrdude-slic3r: verifying ...
avrdude-slic3r: 241630 bytes of flash verified
avrdude-slic3r: safemode: hfuse reads as D8
avrdude-slic3r: safemode: efuse reads as FD
avrdude-slic3r: safemode: Fuses OK (E:FD, H:D8, L:FF)
avrdude-slic3r done. Thank you.
avrdude-slic3r -v -p atmega2560 -c arduino -P COM9 -b 115200 -D -u -U flash:w:1:C:\D A T A\arduino\PRŮŠA\prusa3d_fw_MK3S_3_8_1_2869.hex:i
avrdude-slic3r: Version 6.3-20160220-prusa3d, compiled on Sep 16 2019 at 11:15:49
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
Using Port : COM9
Using Programmer : arduino
Overriding Baud Rate : 115200
avrdude-slic3r: prusa_init_external_flash(): MK3 printer emitted incorrect start code: `echo: `
avrdude-slic3r: arduino_open(): Failed to initialize MK3 external flash programming mode
avrdude-slic3r: Could not open port: COM9
avrdude-slic3r done. Thank you.
avrdude-slic3r -v -p atmega2560 -c wiring -P COM9 -b 115200 -D -U flash:w:0:C:\D A T A\arduino\PRŮŠA\prusa3d_fw_MK3S_3_8_1_2869.hex:i
avrdude-slic3r: Version 6.3-20160220-prusa3d, compiled on Sep 16 2019 at 11:15:49
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
Using Port : COM9
Using Programmer : wiring
Overriding Baud Rate : 115200
AVR Part : ATmega2560
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 10 8 0 no 4096 8 0 9000 9000 0x00 0x00
flash 65 10 256 0 yes 262144 256 1024 4500 4500 0x00 0x00
lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : Wiring
Description : Wiring
Programmer Model: AVRISP
Hardware Version: 15
Firmware Version Master : 2.10
Vtarget : 0.0 V
SCK period : 0.1 us
avrdude-slic3r: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.01s
avrdude-slic3r: Device signature = 0x1e9801 (probably m2560)
avrdude-slic3r: safemode: hfuse reads as D8
avrdude-slic3r: safemode: efuse reads as FD
avrdude-slic3r: reading input file "C:\D A T A\arduino\PRŮŠA\prusa3d_fw_MK3S_3_8_1_2869.hex"
avrdude-slic3r: writing flash (241630 bytes):
avrdude-slic3r: stk500v2_command(): command failed
Writing | ################################################## | 100% 39.09s
avrdude-slic3r: 241630 bytes of flash written
avrdude-slic3r: verifying flash memory against C:\D A T A\arduino\PRŮŠA\prusa3d_fw_MK3S_3_8_1_2869.hex:
avrdude-slic3r: load data flash data from input file C:\D A T A\arduino\PRŮŠA\prusa3d_fw_MK3S_3_8_1_2869.hex:
avrdude-slic3r: input file C:\D A T A\arduino\PRŮŠA\prusa3d_fw_MK3S_3_8_1_2869.hex contains 241630 bytes
avrdude-slic3r: reading on-chip flash data:
Reading | ################################################## | 100% 27.48s
avrdude-slic3r: verifying ...
avrdude-slic3r: 241630 bytes of flash verified
avrdude-slic3r: safemode: hfuse reads as D8
avrdude-slic3r: safemode: efuse reads as FD
avrdude-slic3r: safemode: Fuses OK (E:FD, H:D8, L:FF)
avrdude-slic3r done. Thank you.
avrdude-slic3r -v -p atmega2560 -c arduino -P COM9 -b 115200 -D -u -U flash:w:1:C:\D A T A\arduino\PRŮŠA\prusa3d_fw_MK3S_3_8_1_2869.hex:i
avrdude-slic3r: Version 6.3-20160220-prusa3d, compiled on Sep 16 2019 at 11:15:49
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
Using Port : COM9
Using Programmer : arduino
Overriding Baud Rate : 115200
avrdude-slic3r: prusa_init_external_flash(): MK3 printer emitted incorrect start code: `echo: `
avrdude-slic3r: arduino_open(): Failed to initialize MK3 external flash programming mode
avrdude-slic3r: Could not open port: COM9
avrdude-slic3r done. Thank you.
Tak HW je Arduino MEGA 2560 a ramps 1.4 z Číny, je to deska arduina a schild + drivery motorů, toď vše. Není přiveden ani silový proud pro motory, je jen napájení z USB. Já se vtom nevyznám vůbec ale poku hledá speciální Průšův HW tak ten tam není. Můžu dokoupit ostatní periferie.
Možná firmware pruša nepoběží na číňanovi.
Možná firmware pruša nepoběží na číňanovi.